Panels

Dean Steel Buildings holds Underwriter Laboratory and South Florida Building Code compliance on their panels.

Panel Part Numbers

 

RTA6-200406	RT	Panel Type: PS = PRO SEAM RT = RIB TWELVE RS = RIB SIX SP = SHADOW PANEL FS = FLAT STOCK
	A	For PS: A= 12" wide B= 18" wide C= 24" wide
		For RT, RS, SP: A= Standard B= Left Miter C= Right Miter H= UL 90
	6	Gauge ( 4 - 24 GA, 6 - 26 GA)
	-	Miter or Pitch Code *
	20	Length in feet
	04	Length in inches
	06	Length in sixteenth inches

 

* Miter or Slope Code
A	0:12	J	4:12
B	0.5:12	K	4.5:12
C	1:12	L	5:12
D	1.5:12	M	5.5:12
E	2:12	N	6:12
F	2.5:12	X	SPECIAL
Note:  Dimension for Miter panels should be the overall length.  Miter panels available only for RT and SP type panels.

 

36" Ribbed Panels
Note: Rib Six panel (RS) not shown but is also available.

 

                   RIB TWELVE                                                    SHADOW PANEL

Ribbed Panels are available in Galvalume™, both in 24 and 26 GA (80,000psi Yield), and in different colors (See Color Selection for availability). Special colors (may require minimum order) are also available.

Ribbed Panels notes:
1.  Panels sold as component parts carry no finish guarantees.
2.  Squares are net coverage on width of 36".  Figure end laps as required.
3.  Panels with purlin bearing leg are available in Rib-12 Galvalume™.
4.  Panel availability subject to change without notice.  Check with your Estimator for current availability.

 

 

Pro Seam Panels

 

 

PANEL AVAILABILITY	WGT/SQ
26 GA GLM	92.6
24 GA GLM	118.1
24 GA WHT	127.9

Pro Seam notes:
1.  Pro Seam panels have limited color selections; Non-stock color requires 200sq. minimum order.
2.  All panels are factory notched at both ends.
3.  Oil canning is not a cause for rejection.
4.  Tools required:  Spacer tool (HW9051), shaping tool (HW9052).
5.  See our Pro Seam Requirements for important ordering information.
6.  Export available.  Please call your Estimator for more information

 

Pro Seam Accessories

 

(For Rib-12 panels accessories please see Flashing and Hardware)

	Part No.	Finish	Length/Size	Weight (lbs)
LOW FIXED CLIP	HW9062	Silver	3-3/8"	.13
HIGH FIXED CLIP	HW9063	Silver	4-3/8"	.16
LOW FLOATING CLIP	HW9064	Red	3-3/8"	.97
HIGH FLOATING CLIP	HW9065	Red	4-3/8"	1.1
UTILITY CLIP	HW9066	Silver	3"	.12
LOW EAVE PLATE	AN1276	GNZ	4'-0"	3.7
HIGH EAVE PLATE	AN1277	GNZ	4'-0"	4.7
LOW FIXED RAKE SUPPORT	AN1271	Red	10'-0"	13.7
LOW FLOATING RAKE SUPPORT	AN1272	Red	20'-0"	20.9
HIGH FIXED RAKE SUPPORT	AN1273	Red	10'-0"	16.0
HIGH FLOATING RAKE SUPPORT	AN1274	Red	20'-0"	24.8
BACK-UP PLATE FOR USE AT ENDLAPS AND AT RIDGE, USE OVER PLYWOOD DECK.	HW9103	Red	24"	3.18
	HW9106	Red	18"	2.47
	HW9109	Red	12"	1.77
	HW9112	Red	24"	3.18
CINCH STRAP FOR USE AT ENDLAPS TO COMPLETE THE COMPRESSION JOINT.	HW9104	GLM	24"	.71
	HW9104	COL	24"	.71
	HW9107	GLM	18"	.57
	HW9107	COL	18"	.57
	HW9110	GLM	12"	.42
	HW9110	COL	12"	.42
OUTSIDE CLOSURE 24 GA METAL - FOR USE AT RIDGE, ROOF PENETRATIONS, ETC.	HW9105	GLM	24"	.81
	HW9105	COL	24"	.81
	HW9108	GLM	18"	.65
	HW9108	COL	18"	.65
	HW9111	GLM	12"	.49
	HW9111	COL	12"	.49
INSIDE CLOSURE METAL FOR EXTENDED LIFE	HW9048	GLM		.22
	HW9048	COL		.22
THERMAL SPACER POLYSTYRENE BLOCK USED TO INCREASE THE INSULATION CAPACITY ALONG THE PURLINS. (WITH HIGH SYSTEM ONLY)	HW9049	-	3"x1"x23-7/8" (use with 2"-3" ins)	.09
	HW9114	-	3"x5/8"x23-7/8" (use with 4"-5" ins)	.03
	HW9115	-	3"x3/8"x23-7/8" (use with 6" ins)	.05
SPLICE TAPE SEALER A 100% SOLIDS, BUTYL BASED ELASTOMERIC MATERIAL	HW9050	-	1-5/8"x1/8"x30'	2.3
TAPE SEALER	HW5775	-	1/2"x3/32"x45'	1.4
	HW5721	-	7/8"x3/16"x25'	.8
MINOR RIB TAPE SEALER	HW9113	-	1-3/8"x7/32"x4"	.07
GUTTER SEAL	HW5720	CLR	10.6 oz	.7
SPACER TOOL FOR MAINTAINING PANEL MODULE	HW9021	PVC	24"	2
SHAPING TOOL	HW9052	PVC	3'x6"	5
SELF-DRILLER PLATED STEEL	HW9053	GNZ/COL	1/4"-14x1-1/4" Tek®/2  5/16" hex, no washer closures Purlin bracing to purlin Rake angle to purlin Eave Plate to eave strut Optional clip fastener (Non-UL 90) 2000/CTN	40/CTN
SELF-DRILLER W/SHOULDER PLATED STEEL	HW9054	GNZ	1/4"-14x1-1/4" Shoulder Tek®/2 5/16" hex head, no washer.  Floating rake support to rake angle.  2500/CTN	40/CTN
SELF-DRILLER PLATED STEEL	HW9055	GNZ/COL	1/4"-14x1-1/4" Tek®/2 5/16" hex head with washer. Optional exterior fastener.  UL90 Clip to purlin. 2000/CNT	40/CTN
SELF-DRILLER PLATED STEEL	HW9061	GNZ	#12-24x1-1/4" Tek®/4 5/16" hex head with washer.  Clip to bar joist fastener.  Rake angle to joists.  2500/CTN	68/CTN
SELF-DRILLER ZAC®	HW9057	GNZ/COL	1/4"-14x1-1/4" ZAC® 3/8" hex head with washer. Long life exterior fastener. Light gauge to heavy gauge.  2000/CTN	75/CTN
SELF-TAPPER ZAC®	HW5502	GNZ/COL	#14x3/4" ZAC® 3/8" hex head with washer. Long life exterior fastener. Light gauge to light gauge.   2000/CTN	60/CTN
PRO SEAM RIDGE FLASHING	FRC6-100200	GLM/COL	10'-2"	24.5
	FL4410 for  Ridge Cap closure	GLM/COL		.32
RIDGE SUPPORT ANGLE	ANB4C020400 9" Monovent	GNZ	2'-4"	1.97
	ANB4C021002 12 " Monovent	GNZ	2'-10 1/8"	2.4
PRO SEAM GUTTET BRACKET FIELD ASSEMBLY REQUIRED; FASTENER NOT INCLUDED	HW5647	GNZ	1:12	.6
	HW5648	GNZ	4:12	.6
BRACING STRAP	AN1265	Varies	1-1/2"x100' roll	14
	AN1267	Varies	1-1/2"x25' roll	3.5
VARIABLE TERMINATION TRIM	FTP6-100200	GLM/COL	10'-2"	19.5
	FTP4-100200	GLM/COL	10'-2"	19.5
PRO SEAM RAKE TRIM	FRP6-100200	GLM/COL	10'-2"	19.5
	FRP4-100200	GLM/COL	10'-2"	19.5
PEAK BOX	FNP-010500 Need Slope Code	GLM/COL	1'-5"	1.7
HIGH SIDE SCULPTURED EAVE FLASHING	FEH6-100200	GLM/COL	10'-2"	19.5
SCULPTURED GUTTER END	FL4204	COL	RH	.5
	FL4205	COL	LH	.5
PRO SEAM EAVE FLASHING	FEP6-100200 ( "-" For slope Code)	GLM/COL	10'-2"	4.9
GUTTER	GUA6-200700	COL	20'-7"	29.7
	GUA4-200700	COL	20'-7"	38
RAKE SLIDE	FRS6-100200	COL	10'-2"	3.7
SCULPTURED RAKE TRIM END CAP	FL4217	COL	RH	.6
	FL4218	COL	LH	.6