Structural

Standard zees, cees and Eave Struts

Zees

A = long lap (All holes seen in Picture)
H = Short Lap (does not include black holes in Picture)

Holes are 9/16" in diameter
Slots are 9/16" x 7/8"

Dotted lines on 2nd flange hole represent oversized holes for E-Z lap.

 

 

 

 

Description	Finish	Weight/LF
12 ga. 8" zee/cee	Red Oxide	4.86
12 ga. 8" zee/cee	G-90	5.29
14 ga. 8" zee/cee	Red Oxide	3.55
14 ga. 8" zee/cee	G-90	3.83
15 ga. 8" zee/cee	Red Oxide	3.15
16 ga. 8" zee/cee	Red Oxide	2.85
12 ga. 10" zee	Red Oxide	6.23
14 ga. 10" zee	Red Oxide	4.56
14 ga. 8" eave strut	Red Oxide	4.82
14 ga. 8" eave strut	G-90	5.20

Total lineal footage of the same type gauge is used to determine the per foot cost of that quantity of zees/cees.

Zees are roll formed in lengths from 7 feet to 35 feet; length under 7 feet require special pricing.

 

Channels

OHD - Over Head Door

Blank Channels may not be available.

 

 

 

 

 

 

 

Part No.	Description	WT
CHA-A4-071112	8' wide OHD header	28.3
CHA-A4-091112	10' wide OHD header	35.4
CHA-A4-111112	12' wide OHD header	42.5
CHA-A4-131112	14' wide OHD header	49.6
CHA-A4-151112	16' wide OHD header	56.7
CHA-A4-171112	18' wide OHD header	63.8
CHA-A4-191112	20' wide OHD header	70.9
CH2904	6'-4" wide OHD header	21.4
CH2905	3'-4" wide OHD header	11.3
CHADA4-090100	8' high OHD jamb	32.3
CHAFA4-110100	10' high OHD jamb	39.4
CHAHA4-130100	12' high OHD jamb	46.5
CHAKA4-150100	14' high OHD jamb	53.6
CHAMA4-170100	16' high OHD jamb	60.7
CHAPA4-190100	18' high OHD jamb	67.8
CHASA4-210100	20' high OHD jamb	74.9
CHA-A4-070114	7'-2" high OHD jamb	25.4
CHA-A4-250000	Framing channel	88.8
CHA-A4-200000	Framing Channel	71.0
CH2885	2' OHD jamb extension	10.4
CH2886	4' OHD jamb extension	17.2

 

Eave Struts

* 4 hole end pattern is available upon request.

Punch Patterns

N - low side eave strut
R - high side eave strut 
B - low side w/3'6" roof ext.
C - low side w/6'6" roof ext.
Q - high side w/3'6" roof ext.
P - high side w/6'6" roof ext.

 

 

 

 

 

Part No.	Description	WT
ESN-N4C191112	Eave Strut 1:12, 20' interior Bay	96.3
ESN-N4J191112	Eave Strut 4:12, 20' interior Bay	96.3
ESN-N4C241112	Eave Strut 1:12, 25'  interior Bay	120.4
ESN-N4J241112	Eave Strut 4:12, 25' interior Bay	120.4
ESN-N4C291112	Eave Strut 1:12, 30' interior Bay	144.5
ESN-N4J291112	Eave Strut 4:12, 30' interior Bay	144.5
ESN-N4C200010	Eave Strut 1:12, 19' end Bay	96.7
ESN-N4J200010	Eave Strut 4:12, 19' end Bay	96.7
ESN-N4C250010	Eave Strut 1:12, 24' end Bay	120.8
ESN-N4J250010	Eave Strut 4:12, 24' end Bay	120.8
ESN-N4C300014	Eave Strut 1:12, 29' end Bay	145.0
ESN-N4J300014	Eave Strut 4:12, 29' end Bay	145.0

 

Part Numbering 

1- To order a 14 ga. zee with standard long lap holes punched, 25' 2-1/2" long:

ZEA-A4-250208	Z	Z = Zee
	E	E = 8" x 2.5" T = 10" x 3.5"
	A	Lead Punch Pattern*
	-	X = special punch Z = E-Z lap
	A	Trailing Punch Pattern*
	4	2 = 12 ga.    4 = 14 ga. 5 = 15 ga.    6 = 16 ga.
	-	Slope code (not req'd on zees)
	25	Length in Feet
	02	Length in inches
	08	Length in sixteenth inches

* Dean has a very extensive list of Standard hole patterns available at no extra charge.  But special patterns can also be punched, if necessary (special pricing required).

 

2- To order a 14 ga. channel with A pattern holes punched, 9' 11-3/4" long:

CHA-A4-091112	C	C = Channel
	H	H = 8" x 2.5" F = 8" x 2.5" T = 10" x 4"
	A	Lead Punch Pattern
	-	Hole location for header. - = no holes
	A	Trailing Punch Pattern
	4	2 = 12 ga.    4 = 14 ga. 5 = 15 ga.    6 = 16 ga.
	-	Slope code (not req'd on cees)
	09	Length in Feet
	11	Length in inches
	12	Length in sixteenth inches

 

3- To ordera 14 ga. low side eave strut for a 1:12 pitch buildings, 20' 00-5/8" long:

ESN-N4C200010	ES	E = Eave Strut
	N	Lead Punch Pattern*
	-	n/a
	N	Trailing Punch Pattern*
	4	2 = 12 ga.    4 = 14 ga. 5 = 15 ga.    6 = 16 ga.
	C	A = < .5:12                           C = (.5 to < 1.75):12 E = (1.75 to < 2.75):12          G = (2.75 to 3.75):12 J = (3.75 to 4):12
	20	Length in Feet
	00	Length in inches
	10	Length in sixteenth inches

 

Angles

 

	Part No.	Finish	length/Size	weight
Shelf Angle (2) 9/16" holes 3" apart 5' off center	AN1002	Red Oxide	3"x3"x3/16"   20' long	74.2
	AN1004	Red Oxide	4"x4"x1/4"   20' long	132.0
Sill/Rake Angle	AN1219	GNZ	3"x2" 14 ga. 21' long	22.71
	AN1120	GNZ	2"x5" 14 ga. 10' long	34.9
	AN1116	GNZ	7"x5" 14 ga. 10' long	31.7
Flange Braces	ANF4-FFIISS FF length in feet II length in inches SS length in sixteenths	Red Oxide GNZ	up to 6 feet	0.845/lf
Peak Diaphragms	ANF4-FFIISS FF length in feet II length in inches SS length in sixteenths	Red Oxide GNZ	0.5:12 use 020115 1:12 use 020204 1.5:12 use 020210 2:12 use 020214 3:12 use 020305 4:12 use 020310 5:12 use 020312	0.845/lf

 

Clips

 

	Part No.	Finish	Length/Size	Weight (lbs)
Girt clip Endwall to Sidewall Connection	CH2621	Red Oxide	11 ga. 9/16" hole with 6" & 4 " spacing	4.1
Endwall girt to Sidewall Connection	CL3002	Red Oxide	3/16" Plate 9/16" hole with 4" & 2.5" spacing	10.5
Door jamb base clip	CL3009	Red Oxide	3/16" plate 3/4" & 9/16" hole 3" & 4" spacing	1.3
Girt clip & door clip angle	CL3010	Red Oxide	11 ga. 9/16"x1.25" slots	1.56
Girt to masonry clip	CL3012	Red Oxide	11 ga. 9/16" & 1.25" slots 4" spacing	.9
Door jamb to girt or Eave strut	CL3013	Red Oxide	3/16" plate 9/16" & 1.25" slots	2.4
Friction clip - Girt to jamb	CL3016	Red Oxide	11 ga. 9/16"  hole with 4" and 5.5" spacing includes (2) 0.5"x1.25" bolts and nuts for fastening to the jamb.	2.3
Insert girt clip	CL3185	Red Oxide	3/16" plate 9/16" hole	3.0
Purlin to Purrlin clip	CL3169	Red Oxide	3/16" plate 9/16" hole with 4" & 2 " spacing	4.6
Door jamb to Rafter clip	CL3047	Red Oxide	3/16" plate 9/16" hole 4" spacing	2.3
Channel to Channel clip	CL3063	Red Oxide	3/16" plate 9/16" hole	2.5
Insert girt clip (@ SM RF corner col.)	CL3001	Red Oxide	3/16" plate 9/16" & 1.25" slots	3.1
Slide door header clip	CL3000	Red Oxide	3/16" plate 9/16" hole	4.5
Slide door track hanger	CL3024 (w/8" CH)	Red Oxide	5/16" plate 9/16" & 1" slots
				1.84
Slide door track splice clip	CL3025	Red Oxide	5/16" plate 9/16" & 1" slots 1.25" spacing	4.6